{
  "generated": "2026-10-10",
  "models": [
    {
      "id": "hydraulic-decoiler",
      "unit": 1,
      "name": "Hydraulic Decoiler",
      "short": "Decoiler",
      "tagline": "Hydraulic mandrel expansion, 10 Ton coil pay-off",
      "desc": "The entry end of the line. The coil is loaded hydraulically, the mandrel expands to grip the coil eye and the drive pays strip off at line speed while holding back-tension so the strip stays flat and wrinkle-free into the pinch rolls.",
      "features": [
        "Hydraulic expansion mandrel",
        "Single / double cone design",
        "Heavy duty fabricated structure",
        "Easy coil loading"
      ],
      "specs": [
        [
          "Coil weight",
          "Up to 10 Ton"
        ],
        [
          "Coil width",
          "Up to 1250 mm (line reference)"
        ],
        [
          "Coil ID / OD",
          "508 mm eye / up to 1500 mm OD"
        ],
        [
          "Expansion",
          "Hydraulic"
        ]
      ],
      "dims_mm": {
        "x": 2900,
        "y": 2150,
        "z": 2600
      },
      "groups": [
        {
          "id": "base",
          "label": "Base & foundation"
        },
        {
          "id": "housings",
          "label": "Housings"
        },
        {
          "id": "mandrel",
          "label": "Expansion mandrel"
        },
        {
          "id": "coil",
          "label": "Coil (10 T)"
        },
        {
          "id": "peeler",
          "label": "Hold-down & peeler arm"
        },
        {
          "id": "drive",
          "label": "Drive & hydraulics"
        },
        {
          "id": "controls",
          "label": "Operator controls & guards"
        }
      ],
      "file": "models/hydraulic-decoiler.glb",
      "bytes": 161232,
      "parts": 91,
      "triangles": 3704,
      "viewer": "3d-models.html#hydraulic-decoiler"
    },
    {
      "id": "coil-car",
      "unit": 2,
      "name": "Coil Car",
      "short": "Coil car",
      "tagline": "Hydraulic lift carriage with V-saddle",
      "desc": "Runs on the foundation rails between the coil storage area and the decoiler. The hydraulic saddle lifts the coil to mandrel height and the car traverses in so the coil slides onto the expanded mandrel, taking the crane out of the coil-loading cycle.",
      "features": [
        "Hydraulic lift, V-saddle",
        "Twin machined support rollers",
        "Traction on foundation rails",
        "Crane-free coil loading"
      ],
      "specs": [
        [
          "Coil weight",
          "Up to 10 Ton"
        ],
        [
          "Travel",
          "Along the entry rails"
        ],
        [
          "Lift",
          "Hydraulic cylinder"
        ]
      ],
      "dims_mm": {
        "x": 1900,
        "y": 1150,
        "z": 2400
      },
      "groups": [
        {
          "id": "deck",
          "label": "Deck & frame"
        },
        {
          "id": "saddle",
          "label": "V-saddle & rollers"
        },
        {
          "id": "wheels",
          "label": "Wheels & rails"
        },
        {
          "id": "controls",
          "label": "Pendant control"
        }
      ],
      "file": "models/coil-car.glb",
      "bytes": 49668,
      "parts": 33,
      "triangles": 824,
      "viewer": "3d-models.html#coil-car"
    },
    {
      "id": "pinch-roll-feeder",
      "unit": 3,
      "name": "Pinch Roll & Feeder",
      "short": "Pinch roll",
      "tagline": "Precision pinch rolls with adjustable top roll",
      "desc": "The line drive. Hardened, precision-ground rolls grip the strip and feed it at a constant speed and tension into the slitter head; the air/hydraulic top roll adjustment sets the grip for each thickness from 0.3 mm to 3.0 mm without marking the surface.",
      "features": [
        "Precision machined rolls",
        "Heavy duty gearbox drive",
        "Adjustable top roll",
        "Long service life"
      ],
      "specs": [
        [
          "Pass line",
          "900 mm"
        ],
        [
          "Thickness range",
          "0.3 – 3.0 mm"
        ],
        [
          "Line speed",
          "80 – 120 m/min"
        ]
      ],
      "dims_mm": {
        "x": 2200,
        "y": 1900,
        "z": 2000
      },
      "groups": [
        {
          "id": "base",
          "label": "Base frame"
        },
        {
          "id": "housings",
          "label": "Housings"
        },
        {
          "id": "rolls",
          "label": "Pinch rolls"
        },
        {
          "id": "toproll",
          "label": "Top roll adjustment"
        },
        {
          "id": "drive",
          "label": "Gearbox & motor"
        },
        {
          "id": "guards",
          "label": "Guards, table & controls"
        }
      ],
      "file": "models/pinch-roll-feeder.glb",
      "bytes": 118380,
      "parts": 62,
      "triangles": 2696,
      "viewer": "3d-models.html#pinch-roll-feeder"
    },
    {
      "id": "slitter-head",
      "unit": 4,
      "name": "Slitter Head",
      "short": "Slitter head",
      "tagline": "Precision knife arbors — strip width accuracy ±0.10 mm",
      "desc": "Two hardened knife arbors shear the full coil width into the required number of strips in one pass. Knife spacing sets the strip width; strip width accuracy is held to ±0.10 mm, and the arbors can be re-set for any strip combination the customer needs.",
      "features": [
        "Twin hardened knife arbors",
        "Strip width accuracy ±0.10 mm",
        "Number of strips as per requirement",
        "Quick knife re-setting for new widths"
      ],
      "specs": [
        [
          "Coil width",
          "1250 mm (line reference)"
        ],
        [
          "Thickness range",
          "0.3 – 3.0 mm"
        ],
        [
          "Strip width accuracy",
          "±0.10 mm"
        ],
        [
          "No. of strips",
          "As per requirement"
        ]
      ],
      "dims_mm": {
        "x": 2400,
        "y": 2050,
        "z": 3200
      },
      "groups": [
        {
          "id": "base",
          "label": "Base & housings"
        },
        {
          "id": "lower-arbor",
          "label": "Lower knife arbor"
        },
        {
          "id": "upper-arbor",
          "label": "Upper knife arbor"
        },
        {
          "id": "holddown",
          "label": "Hold-down & strip guides"
        },
        {
          "id": "drive",
          "label": "Drive train"
        },
        {
          "id": "controls",
          "label": "Guards & controls"
        }
      ],
      "file": "models/slitter-head.glb",
      "bytes": 222860,
      "parts": 117,
      "triangles": 6000,
      "viewer": "3d-models.html#slitter-head"
    },
    {
      "id": "scrap-winder",
      "unit": 5,
      "name": "Hydraulic Scrap Winder",
      "short": "Scrap winder",
      "tagline": "Continuous edge-trim scrap winding",
      "desc": "Takes the two edge trim strips away from the slitter head and winds them into tight, easily handled coils. Hydraulically driven with a slipping clutch action, it keeps winding at a constant tension so trim never piles up on the floor or snags the line.",
      "features": [
        "Robust construction",
        "Smooth scrap winding",
        "Hydraulic drive",
        "Low maintenance"
      ],
      "specs": [
        [
          "Scrap",
          "Edge trim from both sides"
        ],
        [
          "Drive",
          "Hydraulic"
        ],
        [
          "Mounting",
          "Floor mounted, downstream of slitter head"
        ]
      ],
      "dims_mm": {
        "x": 1900,
        "y": 1650,
        "z": 2200
      },
      "groups": [
        {
          "id": "base",
          "label": "Base & pedestal"
        },
        {
          "id": "winder",
          "label": "Winding shaft & flanges"
        },
        {
          "id": "drive",
          "label": "Hydraulic drive"
        },
        {
          "id": "guards",
          "label": "Guards & controls"
        }
      ],
      "file": "models/scrap-winder.glb",
      "bytes": 100604,
      "parts": 56,
      "triangles": 2328,
      "viewer": "3d-models.html#scrap-winder"
    },
    {
      "id": "tension-stand",
      "unit": 6,
      "name": "Tension Stand",
      "short": "Tension stand",
      "tagline": "Pad / bridle drag for tight, even recoiling",
      "desc": "Sits between the slitter head and the recoiler and applies controlled drag to every strip. That back-tension is what makes the finished slit coil wind tight and square instead of loose and telescoped, and it keeps the strips from wandering sideways.",
      "features": [
        "Pad-type tension unit",
        "Uniform drag across full width",
        "Hardened contact rolls",
        "Adjustable for strip thickness"
      ],
      "specs": [
        [
          "Function",
          "Back tension before recoiling"
        ],
        [
          "Width covered",
          "1250 mm (line reference)"
        ],
        [
          "Setting",
          "Adjustable for thickness 0.3 – 3.0 mm"
        ]
      ],
      "dims_mm": {
        "x": 2000,
        "y": 1900,
        "z": 1800
      },
      "groups": [
        {
          "id": "base",
          "label": "Base & side frames"
        },
        {
          "id": "rolls",
          "label": "Contact rolls"
        },
        {
          "id": "pad",
          "label": "Pressure pad & screws"
        },
        {
          "id": "guides",
          "label": "Strip guides & instruments"
        }
      ],
      "file": "models/tension-stand.glb",
      "bytes": 64780,
      "parts": 43,
      "triangles": 1316,
      "viewer": "3d-models.html#tension-stand"
    },
    {
      "id": "separator",
      "unit": 7,
      "name": "Separator",
      "short": "Separator",
      "tagline": "Lane-by-lane strip separation before recoiling",
      "desc": "A guide disc sits in every slit line, so each strip enters the recoiler in its own lane with a clean gap. That is what stops strips from overlapping, cross-winding or telescoping on the finished coil — and it is why the recoiled coil comes off tight and square.",
      "features": [
        "One separator disc per slit line",
        "Side guides for edge control",
        "Idler discs — no marking",
        "Quick change for new strip widths"
      ],
      "specs": [
        [
          "Strip pitch",
          "Set to the slitter knife spacing"
        ],
        [
          "No. of strips",
          "As per requirement"
        ],
        [
          "Mounting",
          "Between tension stand and recoiler"
        ]
      ],
      "dims_mm": {
        "x": 1900,
        "y": 1750,
        "z": 1700
      },
      "groups": [
        {
          "id": "base",
          "label": "Base & side frames"
        },
        {
          "id": "discs",
          "label": "Separator discs"
        },
        {
          "id": "guides",
          "label": "Edge guides & rolls"
        },
        {
          "id": "adjust",
          "label": "Adjustment & guards"
        }
      ],
      "file": "models/separator.glb",
      "bytes": 80832,
      "parts": 50,
      "triangles": 1856,
      "viewer": "3d-models.html#separator"
    },
    {
      "id": "hydraulic-recoiler",
      "unit": 8,
      "name": "Hydraulic Recoiler",
      "short": "Recoiler",
      "tagline": "High torque winding with hydraulic expansion",
      "desc": "Re-winds the slit strips into a tight finished coil. Hydraulic mandrel expansion grips the coil eye, a high torque drive maintains constant strip tension as the coil diameter grows, and a hydraulic push-off arm slides the finished coil clear of the mandrel.",
      "features": [
        "Hydraulic expansion mandrel",
        "High torque drive",
        "Smooth and uniform winding",
        "Suitable for all coil types"
      ],
      "specs": [
        [
          "Coil weight",
          "Up to 10 Ton"
        ],
        [
          "Coil width",
          "1250 mm (line reference)"
        ],
        [
          "Suitable for",
          "CR, HR, GI, PPGL, SS"
        ],
        [
          "Push-off",
          "Hydraulic"
        ]
      ],
      "dims_mm": {
        "x": 3000,
        "y": 2200,
        "z": 2900
      },
      "groups": [
        {
          "id": "base",
          "label": "Base & foundation"
        },
        {
          "id": "housings",
          "label": "Housings"
        },
        {
          "id": "mandrel",
          "label": "Expansion mandrel"
        },
        {
          "id": "coil",
          "label": "Finished coil"
        },
        {
          "id": "pushoff",
          "label": "Hydraulic push-off arm"
        },
        {
          "id": "drive",
          "label": "Drive & hydraulics"
        },
        {
          "id": "safety",
          "label": "Railing & controls"
        }
      ],
      "file": "models/hydraulic-recoiler.glb",
      "bytes": 162956,
      "parts": 88,
      "triangles": 3852,
      "viewer": "3d-models.html#hydraulic-recoiler"
    },
    {
      "id": "exit-car",
      "unit": 9,
      "name": "Exit Car",
      "short": "Exit car",
      "tagline": "Takes the finished coil off the mandrel",
      "desc": "The finished coil is pushed off the recoiler mandrel onto the exit car, which lowers it to the floor and traverses it clear of the line for strapping and crane pick-up. It keeps the recoiler free for the next coil instead of waiting on overhead crane handling.",
      "features": [
        "Hydraulic lift and lower",
        "Machined carrying rollers",
        "Traverses on foundation rails",
        "Quick coil removal cycle"
      ],
      "specs": [
        [
          "Coil weight",
          "Up to 10 Ton"
        ],
        [
          "Travel",
          "Along the exit rails"
        ],
        [
          "Lift",
          "Hydraulic cylinder"
        ]
      ],
      "dims_mm": {
        "x": 1800,
        "y": 1000,
        "z": 2300
      },
      "groups": [
        {
          "id": "deck",
          "label": "Deck & frame"
        },
        {
          "id": "rollers",
          "label": "Carrying rollers"
        },
        {
          "id": "wheels",
          "label": "Wheels & rails"
        },
        {
          "id": "controls",
          "label": "Pendant & hoses"
        }
      ],
      "file": "models/exit-car.glb",
      "bytes": 49448,
      "parts": 33,
      "triangles": 868,
      "viewer": "3d-models.html#exit-car"
    },
    {
      "id": "control-panel",
      "unit": 10,
      "name": "Electrical Control Panel",
      "short": "Control panel",
      "tagline": "Single-operator line control with HMI",
      "desc": "One operator runs the whole line from here — pay-off, feeding, slitting and recoiling speeds, hydraulic pressure and coil handling. The HMI screen shows line speed, strip count and running status, with hard-wired pushbuttons and an E-stop alongside it for safety.",
      "features": [
        "Single-operator line control",
        "HMI screen with line status",
        "Pushbutton and selector controls",
        "E-stop and safety interlocks"
      ],
      "specs": [
        [
          "Control",
          "Single operator station"
        ],
        [
          "Drive control",
          "Line speed 80 – 120 m/min"
        ],
        [
          "Indication",
          "Speed, status, fault"
        ]
      ],
      "dims_mm": {
        "x": 1100,
        "y": 1700,
        "z": 1000
      },
      "groups": [
        {
          "id": "cubicle",
          "label": "Cubicle & base"
        },
        {
          "id": "desk",
          "label": "Sloped desk"
        },
        {
          "id": "hmi",
          "label": "HMI & instrumentation"
        },
        {
          "id": "buttons",
          "label": "Pushbuttons & E-stop"
        },
        {
          "id": "services",
          "label": "Cable duct & services"
        }
      ],
      "file": "models/control-panel.glb",
      "bytes": 63056,
      "parts": 44,
      "triangles": 1068,
      "viewer": "3d-models.html#control-panel"
    },
    {
      "id": "coil-slitting-line-1250",
      "unit": 0,
      "name": "Coil Slitting Line — 1250 mm (assembled)",
      "short": "Full line",
      "tagline": "All nine units plus the control panel, in line sequence",
      "desc": "The complete 1250 mm coil slitting line assembled from the individual machine models, in running order with the strip path.",
      "features": [
        "Coil width 1250 mm",
        "Thickness range 0.3 – 3.0 mm",
        "Coil weight 10 Ton",
        "Slitting speed 80 – 120 m/min",
        "Strip width accuracy ±0.10 mm",
        "No. of strips: as per requirement"
      ],
      "specs": [
        [
          "Units",
          "9 + electrical control panel"
        ]
      ],
      "dims_mm": {
        "x": 20800,
        "y": 2200,
        "z": 4300
      },
      "groups": [
        {
          "id": "hydraulic-decoiler",
          "label": "Hydraulic Decoiler"
        },
        {
          "id": "coil-car",
          "label": "Coil Car"
        },
        {
          "id": "pinch-roll-feeder",
          "label": "Pinch Roll & Feeder"
        },
        {
          "id": "slitter-head",
          "label": "Slitter Head"
        },
        {
          "id": "scrap-winder",
          "label": "Hydraulic Scrap Winder"
        },
        {
          "id": "tension-stand",
          "label": "Tension Stand"
        },
        {
          "id": "separator",
          "label": "Separator"
        },
        {
          "id": "hydraulic-recoiler",
          "label": "Hydraulic Recoiler"
        },
        {
          "id": "exit-car",
          "label": "Exit Car"
        },
        {
          "id": "control-panel",
          "label": "Electrical Control Panel"
        }
      ],
      "file": "models/coil-slitting-line-1250.glb",
      "bytes": 1039472,
      "parts": 617,
      "triangles": 24584,
      "viewer": "3d-models.html#line"
    }
  ]
}